Видео

We have the same issue except it is intermittent. Most of the time the oven works but sometimes it will only get up to 175 degrees and we can see the glow of a flame. Do you think the ignitor is the cause?

Thank you so much for the video. I have plan to do exactly what you did😅😅😅

Thanks for sharing. I'm planning to use just the batteries, a DC/AC inverter, the 24V DC motor and a permanent magnet generator (output of 220V). The motor will power, (rotate), the permanent magnet generator. I will get current from generator to feed my equipment and feed the inverter which will keep my batteries up to the task. I hope to reduce my energy costs and be ''off-grid'' at least 80% (eventually). Energy costs are sky-rocketing and will prevent any ''hit to my pocket'' down the road. Again, thanks for sharing.

Thank you so much!!🎉😺

Hello dear sir can your ebike reverse now that way of fixing your bicycle 😊😅

Battery is good, what would be the problem in my car can't start even in jump start.

Thanks so much for your great instructions. Worked like a charm. We have the exact same oven. It would cycle on and start to heat up then it would cycle off. Kept repeating that on and off. Now I am cooking with gas! Lol

Very informative and very detailed video. Thank you for posting.

Excellent video

Weak frame push bike no.

Not sure why you have to take all that out. Just put in a tray to hold charcoal, remove burners, gas hoses/tank and go. That way you can turn it back into gas.

I'm buying the 1000watt viribus conversion on ebay where do I get the battery.

Good luck when it blows up in the moddle of the night ... 😂🎉🎉🎉

Cool video. You made the install look so easy. I'd like to try this on my bike. Thanks for the content.

ARE THE CONVERSION KITS MORE POWERFUL THAN THE ONES INSTALLED ON MANUFACTURED ELECTRIC BIKE?

I PREFER DISC BRAKES FOR BETTER STOPPING POWER. CAO THE BIKE CONVERSION BE DONE WITH DISC BRAKES ON THE BIKE?

I have a 06 gto. I thought my starter went out so I swapped it out, but got the new part in and it didn’t work. I was able to get the starter to engage by touching a socket extension onto the two terminals onto the starter, with the key on the on position the car started. When I turn the key, the starter relay clicks. Does that mean from the relay to the starter something is wrong? I’m kinda broke so I’m not able to pay someone to figure it out for me 😭

Just trying to learn how the different parts of my motorcycle work and this is very helpful. Thank you

Thank you this video was great

Please how did you get the complete kit? Where do I get them?

How do you know if the battery pack is compatible with the controller box or the motor

How do you know if the battery pack is compatible with the controller box or the motor

Is it too difficult to straighten the wires to make the connections clearer?

There's probably nothing actually wrong with your existing lamp socket ... LED bulbs that only feature an On/Off lighting option don't work with 3-way switches. You could have just purchased an LED light bulb with 3-way lighting options from your local Home Depot ... However, switching out the socket does accomplish the same thing!

This is the best video on RUclips. No bs not 1000ads and hes not trying to sell you an ebike thst costs more than your nans morhers house 😂. Happy riding guys !!!!

Great video. If I want to use this type of motor as a generator can I use just the three phase wires to extract the electricity ?

Hello dear that's much better and more lighter 😊😅

Can I please get the link to the igniter

Helpfulness ❤

BTW this is still in an issue the highland model 3

Greeting, it's a very good place to put the battery and controller there. The bike needs balancing for easy control and tire wear mitigation.🙂

Young lust

2:23 I have 48 volt batteries would I be able to use some kind of a resistor or would I be able to use that?

Please link to buy the controller?

Is there anyway of increasing the power, using products from companies like Arduino

awesome video and very helpful. It's so nice to be able to buy a $30 replacement piece and fix the stove in 10-15 minutes, and not have to worry about paying a repair guy

Hi - great video! Makes the repair look really easy. May I ask what model number your oven is? It looks very similar to mine but I wanted to double check before pulling the trigger on the part.

thank you my controller had a different wire than the battery and your the only tutorial that actually showed how to cut and connect the wires

Sorry, man, but you made a LOT of mistakes! Those Wagner pads came with a small packet of grease, that is intended to be lightly smeared between the pad and the shim. Then, use brake grease on all the metal to metal contact points, especially on the fitment kit and the caliper ring and horns. Don't bleed the fluid out! Now that you have bled the fluid out, you have a low amount of brake fluid. Fluid is to be FULL when the brakes are new and will be near "Min" when the pads are worn. So you now have the fluid below Max with new pads, and will have a level below Min when the pads wear. Not at least checking the rotors for thickness and runout is "iffy". Def should re-surface or replace them or you are just shortening the life of the pads and will soon get some warping. AND: REMIND PEOPLE TO PUMP THE BRAKES UNTIL FIRM, or they WILL have no brakes when they start the car!

I really enjoyed your video. My Weber Spirit (2 burner) is in its 11th year of use and it looks rough, but works well. It won’t be too much longer before I do this conversion. Hopefully, finding the proper size charcoal grate won’t be too tough!

You made this so easy to do. I absolutely love DIY especially since I don’t have to bother the hubby another honey-do. It’ll just add on to the list anyway! 😂. I’ve subscribed to you and look forward to more of your videos.

You give a Fabulous explanation and do excellent camera work!

I have a 12V 18ah battery. What is the best suitable solar panel to charge it?

My O2 sensor Bank 2 Sensor 2 was replaced on 3.5 liter V6 2008 Camry engine with 220,000 miles, but the old one came out stripped on top where it screws and fits tightly. So the mechanic could not get the new one to fit tightly because the pipe hole was larger because the old one was stripped and forced to install in place before I bought the car in 2019. So now I have this harsh coarse engine start up and acceleration sound (sounds like an old 5.0 liter V8 engine) with a check engine light. The pipe that is underneath the car where the 02 sensor is connected to is rusted. The mechanic told me that needs to be replaced. I don't know to what to do about getting it repaired since I need it to drive until I can purchase another car on June 22. I have put $1500 dollars in it with new ignition coil and battery in past 3 weeks. My gas mileage is still good with 20.8. I am not running the A/C because that is when the check engine came on. So, I burning up in this Texas heat.

Really good video, thanks for doing this...ordered my part tonight.

You do not need to remove the brake caliper bolt. Just put the 22mm socket on the other side of the strut with the impact gun. The impact gun is your friend, folks

Any idea how to remove the cover off of the incinerator evolution? I love this video by the way appreciate the detail.

Best video on this subject.

Thanks for the help!! Your video made changing our igniter a breeze!! We knew exactly what we were doing! Thanks again!!

Thank you brother